CR 90 corvette 3d print with many mods

thebeans

Well-Known Member
I've had a friend print off a cr90 corvette using the Gambody files which are not very accurate so I'm making several modifications by hand to the overall model using techniques such as kitbashing ,scratch building, a bit of trash bash too in order to make it more decent and estetically pleasing. First up was the bridge interior and exterior followed by the cannons.
 

Attachments

  • 20220228_093525.jpg
    20220228_093525.jpg
    665.4 KB · Views: 139
  • 20220228_093615.jpg
    20220228_093615.jpg
    1.6 MB · Views: 120
  • 20220228_093630.jpg
    20220228_093630.jpg
    748.1 KB · Views: 109
  • 20220309_204514.jpg
    20220309_204514.jpg
    1.5 MB · Views: 104
  • 20220309_212335.jpg
    20220309_212335.jpg
    1.2 MB · Views: 105
  • 20220310_221006.jpg
    20220310_221006.jpg
    1.4 MB · Views: 104
  • 20220310_221745.jpg
    20220310_221745.jpg
    1.5 MB · Views: 104
  • 20220311_211650.jpg
    20220311_211650.jpg
    699.1 KB · Views: 102
  • 20220313_222455.jpg
    20220313_222455.jpg
    543.5 KB · Views: 97
  • 20220314_233053.jpg
    20220314_233053.jpg
    387.7 KB · Views: 88
  • 20220315_112226.jpg
    20220315_112226.jpg
    470.6 KB · Views: 91
  • 20220318_212247.jpg
    20220318_212247.jpg
    593.5 KB · Views: 87
  • 20220318_212218.jpg
    20220318_212218.jpg
    707.4 KB · Views: 86
  • 20220318_212323.jpg
    20220318_212323.jpg
    369.8 KB · Views: 85
  • 20220318_212435.jpg
    20220318_212435.jpg
    1,011.2 KB · Views: 91
  • 20220318_212505.jpg
    20220318_212505.jpg
    586.1 KB · Views: 108
  • 20220318_212557.jpg
    20220318_212557.jpg
    920.1 KB · Views: 147

thebeans

Well-Known Member
The ultimate aim of this build will be to present it as a CR corvette variant with a different colour scheme to the tantive IV ( not decided upon yet) a great bulk of the work will be covering 3d print layer lines with ultra thin styrene then greeblieing on top ,so far I've used some 1/72 airfix british airborne willys jeep parts.The overall length of the ship will be 1 meter.
 

thebeans

Well-Known Member
That turned out pretty nice. Was the Gambody stuff accurate with the overall shape though?

TazMan2000
It's close but i would not call it accurate overall , it has issues everywhere but it has a good basis for the work i have planned ....and that's a LOT of work. It would look fine to most eyes out of the box/ direct from the files but i would never be happy with it that way.
 

thebeans

Well-Known Member
I have a few engine heat sinks to build.
 

Attachments

  • 20220327_203150.jpg
    20220327_203150.jpg
    587.2 KB · Views: 35
  • 20220327_210054.jpg
    20220327_210054.jpg
    1.1 MB · Views: 33
  • 20220327_210113.jpg
    20220327_210113.jpg
    1.3 MB · Views: 35
  • 20220327_210142.jpg
    20220327_210142.jpg
    707.9 KB · Views: 33
  • 20220327_210207.jpg
    20220327_210207.jpg
    522.7 KB · Views: 31

thebeans

Well-Known Member
Not much to report on this past couple of weeks but I'm getting something done in the way of modifications
 

Attachments

  • 20220408_225257.jpg
    20220408_225257.jpg
    659 KB · Views: 25
  • 20220408_225450.jpg
    20220408_225450.jpg
    667.1 KB · Views: 22
  • 20220408_225156.jpg
    20220408_225156.jpg
    678.6 KB · Views: 22
  • 20220408_225204.jpg
    20220408_225204.jpg
    611.5 KB · Views: 20
  • 20220408_225247.jpg
    20220408_225247.jpg
    1.2 MB · Views: 25

Your message may be considered spam for the following reasons:

  1. Your new thread title is very short, and likely is unhelpful.
  2. Your reply is very short and likely does not add anything to the thread.
  3. Your reply is very long and likely does not add anything to the thread.
  4. It is very likely that it does not need any further discussion and thus bumping it serves no purpose.
  5. Your message is mostly quotes or spoilers.
  6. Your reply has occurred very quickly after a previous reply and likely does not add anything to the thread.
  7. This thread is locked.
Top