Bam's WIP

Bam

New Member
Hi fellow Hunters,

like my buddy Uhlakk ive decided to start a WIP thread also to show u how far im coming. After i found the Lair i decided immidiatly to create one, the hunger for Costumes was born when i joined the 501st Legion and since then i create Costumes.

Long Story short, here is what ive got so far:

Let me introduce SAM to u:
DSCN0749.jpg


Hes wearing my Undersuit that i have to seal with Latex and then i will seperate Top and Bottom^^

My P1 Bio Helmet (from Uhlakk) and my P1 Mask (from Monsterroom, thx ur the best)
DSCN0741.jpg


Yesterday ive started making the Dreads, long ones and short ones and all i cann say Backr rods work very good with heat^^
DSCN0743.jpg

I made 49 Long ones

DSCN0744.jpg

and 26 short ones

2 Pics of my Lair where the dream comes True :lol:
DSCN0754.jpg

DSCN0753.jpg


and at last my pride.....The Spear ;)
DSCN0734.jpg

DSCN0735.jpg


i think i will start painting the Mask this or next week and then new Pics will follow, and i have to buy Latex which isnt so cheap but in septembre i have Birthday Muahahahahaha

DSCN0749.jpg


DSCN0741.jpg


DSCN0743.jpg


DSCN0744.jpg


DSCN0754.jpg


DSCN0753.jpg


DSCN0734.jpg


DSCN0735.jpg
 
That spear looks great, where did you get it?
Good start on your costume, what kind are you going for? P1, P2, something own?

I got the Spear from Ebay

Im going to make my Own Yautja, im mixing diferent colors on my Head and Body Templates to see what i gonna take.
 
That pleats on the side are terrible, isn't it?

I have the same problem and thoght it musst be possible to cut out the wasted material and latex it on an other underground, like a narrow turtleneck or something like that!
The sides should be smooth than...

but yours is in one piece and I only have the upper part (I go for two pieces, better to wear I hope)
 
Small Update:

i have now the concept for my first Pred suit and u all now this Concept if u have read the thread :lol:

I talked to Wolfie138 and he gives his ok and would be proud if this comes to life so here is the Pred im gonna make:

breacher.jpg


THE BREACHER

i think i do some little changes but not so big ones 'cause the whole art is damn good enough :lol:

so let the fun begin. Pics of my Mask will follow this Week.

breacher.jpg
 
OK, New Update:

Ive completed the Mask so far, i only need the dreads^^
And i must say for my first Big Paintjob with a Airbrushpistol im very very proud of myself, but take a look for urself.....

DSCN0790.jpg
DSCN0791.jpg
dscn0792.jpg


And a Picture with it on my face and a pic with attached quills...

dscn0793.jpg
DSCN0796.jpg


there will be new pics when i finished my dreads so stay on :lol:

DSCN0790.jpg


DSCN0791.jpg


dscn0792.jpg


dscn0793.jpg


DSCN0796.jpg
 
Hey mate....you really want themask that way?

I think the paintjob looks very scatchy. You should bring some depth into it.

But for the first time airbrushing. not bad man.

Couldn't do it better (till I have my new fine nozzel)
 
Wow! That pred design looks hardcore, you wouldn't want to mess with that guy! Oh and good work on your mask, it looks great!
 
So tonight (German Time) i will be back in my lair to do some work.

-Covering the dreads with latex

-Design a new Bio

-Wiring my lasers together and test them

-Attaching new Muscles to the suit

-start building the Backpack and the Frontplate

-Start building the shins

-Cut the Net for the Suit into the right position

so its a lot of work to do but i will make pics and tomorrow u can see the progress ;)
 
This thread is more than 14 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top