Hi guys i have here one of the helmets from the anime show Tekkaman Blade / Teknoman Blade from the early 90's. This helmet is of Tekkaman Blade the good guy from the show.
I am up to the stag of molding and casting the helmet. I am planning on doing a run of 20 or until the molds need repair. I am going to have to options at this stage 1. is raw casts and the other is going to be fully finished helmet. the helmet is 19 cm from ear to ear and 23 cm from nose to back.
The raw cast option is going to be 1 Raw cast helmet 2 ears ( 1 right and 1 left) 1 yellow forehead gem and 1 green tinted visor. this kit will cost $300 USD plus postage world wide. This kit will need some filling and sanding also the visor section will need to be cut out. The helmet will need to be primed and painted.
The fully finished kit with be a helmet will be fully sanded, painted the visor and forehead gem attached. the ears will be separate and you will need to glue them into the sockets. The helmet will also have foam padding on the inside. It is going to cost $500 USD plus shipping world wide.
A down payment of $100 USD for the raw casts and a $150 USD for the fully finished
Each ear is roughly 500mm long which will mean the kits will be shipped in two boxes one for the helmet and the other for the two ears. Here is a link to the build page on this helmet.
http://www.therpf.com/showthread.php?t=253181
I hope to start pulling casts middle to end of august.
I need 10 people with down payments before i start casting.
Here are a few pics of the helmet at this stage.
1. Juajn7ernandez ( undecided on Kit )
2. CLGeekboy ( Fully Finished )
3.
4.
5.
6.
7.
8.
9.
10.
I am up to the stag of molding and casting the helmet. I am planning on doing a run of 20 or until the molds need repair. I am going to have to options at this stage 1. is raw casts and the other is going to be fully finished helmet. the helmet is 19 cm from ear to ear and 23 cm from nose to back.
The raw cast option is going to be 1 Raw cast helmet 2 ears ( 1 right and 1 left) 1 yellow forehead gem and 1 green tinted visor. this kit will cost $300 USD plus postage world wide. This kit will need some filling and sanding also the visor section will need to be cut out. The helmet will need to be primed and painted.
The fully finished kit with be a helmet will be fully sanded, painted the visor and forehead gem attached. the ears will be separate and you will need to glue them into the sockets. The helmet will also have foam padding on the inside. It is going to cost $500 USD plus shipping world wide.
A down payment of $100 USD for the raw casts and a $150 USD for the fully finished
Each ear is roughly 500mm long which will mean the kits will be shipped in two boxes one for the helmet and the other for the two ears. Here is a link to the build page on this helmet.
http://www.therpf.com/showthread.php?t=253181
I hope to start pulling casts middle to end of august.
I need 10 people with down payments before i start casting.
Here are a few pics of the helmet at this stage.
1. Juajn7ernandez ( undecided on Kit )
2. CLGeekboy ( Fully Finished )
3.
4.
5.
6.
7.
8.
9.
10.
Attachments
-
IMAG3753.jpg903.4 KB · Views: 173
-
IMAG3769.jpg881.3 KB · Views: 139
-
IMAG3766.jpg895.9 KB · Views: 196
-
IMAG3765.jpg900.3 KB · Views: 313
-
IMAG3763.jpg893.3 KB · Views: 520
-
IMAG3762.jpg899.6 KB · Views: 182
-
IMAG3760.jpg896.6 KB · Views: 165
-
IMAG3759.jpg910.8 KB · Views: 123
-
IMAG3757.jpg924.9 KB · Views: 119
-
IMAG3756.jpg902.4 KB · Views: 140
Last edited: