Recent content by Yorisu

Yes i know conrad but infortunatly there are no conrad's store near me :( Same in my city, no little electronics store, ebay is my only friend ! :lol

No i live in france, only internet can help me :) I have a little kit of resistors and caps that i bought to start my project. If i continue in that way to improve my suit or even the helmet i think i'll buy a complet kit ;)

Hi ! so i just bought some 56 ohm and a VRegulator +5 7805, so in approximatly 1 week i have all the stuff :) I'll give some new when i'll get it all ;) DevilFlash ! xl97 ! Thank for your help :thumbsup

Perfectly clear now ^^ So i just find some 10uF cap and 1KOhm resistors, but no LM7805 +5v vol regulator, i'll give it a try like that by following your diagram. I'll come back with the results later. Don't worry xl97, i've learn about the +5v pin on the arduino ;)

Ok so for DevilFlash i use xl97's diagram in post #1213, so must i have 1k Ohm ? and 2x10uF ? This is really confusing :wacko For xl97 i used you code on each servo and work well, each servo do the movement perfectly.

Ok so i saw that for a 7.4v batterie like mine i need 220Ohm resistors For the capacitors i can't find a correctly kits with all kind of cap, ceramic are pF and electrolytic are uF. I'm not really an expert in this and i don't know what choose :cry

Ok i'll buy one, thank you :) and about capacitor ? Are those ok ? : NTE VHT.1M50 - CAP-0.1MF 50V 105*C RADIAL LEAD Radial Capacitor : Electrolytic Capacitors | RadioShack.com NTE VHT.33M50 - CAP-0.33MF 50V 105*C RADIAL LEAD Radial Capacitor : Electrolytic Capacitors | RadioShack.com And finally...

Yes capacitor sorry :p There are many kind of capacitor (exempl : 0.33uF for 50v or 1400v or 64v) and i don't know wich to choose :behave Yes it's a +5v like in my link LM78M05CT 5V 0.5A Voltage Regulator - RobotShop it's exactly the same ^^

I just plugged a wire in the GnD plug after the 13th one, and it seems that my button responding a bit more, but always one servo responding :( must i buy some 0.33 UF and 0.1UF condensator ?

I tested my second servo and it's fine, nothing broken. The resistor that i use are 10.3 ohms ( Brown black orange thin sliver and gold) The voltage regulator is a +5v yes LM78M05CT 5V 0.5A Voltage Regulator - RobotShop And finally the transistors are 2N3904

Ok! I'm back! So I followed your diagram XL97 (I just have not put the following items: .33 UF and 0.1UF because I do not have them at all) and I used the code memebr modify Devilflash (on facebook ) and here the result: - the LEDs are less bright - the button respond well but the activation...

I use a 7.4V 2200mAh Lipo battery for power. The servo is connected to the +5 v, the photo was taken at an angle that's why we believe that is connected to the 3.3v. I tried several code from this thread, and the one working the "best" is the one memebr's. The LED perfectly fade, but the servo...

Ok ! Here we go :

Hi everyone! First I'm sorry for my bad english but I'm french :D Good job for the clear tutorial but I have a problem. I realize the pattern exactly as described in post 1 with exactly the same component exept the servo motor, i use this one : BMS-616MGplusHS Super Strong Servo (Mos-FET) for...