Put some scuffs ad scratches, just basically following the weathering patterns from reference pics. Did a quick test fit to see how everything was loo

Put some scuffs ad scratches, just basically following the weathering patterns from reference pics. Did a quick test fit to see how everything was loo

  • 0
  • 0
Sanded the texture back and applied the matt black to the texured area. Next I will mask of the areas to lay the chrome down

Sanded the texture back and applied the matt black to the texured area. Next I will mask of the areas to lay the chrome down

  • 0
  • 0
Laid down a layer of the texture paint

Laid down a layer of the texture paint

  • 0
  • 0
Heres the masked areas ready to apply the texture paint

Heres the masked areas ready to apply the texture paint

  • 0
  • 0
16

16

  • 0
  • 0
Heres the spaz stick high gloss black layer. I figured I would just spray the entire piece and then mask off the areas for the texure next.

Heres the spaz stick high gloss black layer. I figured I would just spray the entire piece and then mask off the areas for the texure next.

  • 0
  • 0
Decided on using this spaz stix as basically there wasnt any other way of doing the chrome areas properly with going the route of electroplating etc

Decided on using this spaz stix as basically there wasnt any other way of doing the chrome areas properly with going the route of electroplating etc

  • 0
  • 0
Close up of the texture

Close up of the texture

  • 0
  • 0
Got a matt black color onto the dome area. Then applied the same texture spray to it and sanded it back until it was a little flatter. Again I used re

Got a matt black color onto the dome area. Then applied the same texture spray to it and sanded it back until it was a little flatter. Again I used re

  • 0
  • 0
Quickly put everything together just to see how it fit. The fibreglass on the inside of the dome area needs to be sanded a bit where it meets the face

Quickly put everything together just to see how it fit. The fibreglass on the inside of the dome area needs to be sanded a bit where it meets the face

  • 0
  • 0
Heres a progress hot of the pieces so far... The dome area was a nightmare. The texture when sanded becomes furry and couldnt see how I was going to p

Heres a progress hot of the pieces so far... The dome area was a nightmare. The texture when sanded becomes furry and couldnt see how I was going to p

  • 0
  • 0
Close up of the finish of the left side of the face plate

Close up of the finish of the left side of the face plate

  • 0
  • 0
Close up of the finish of the right side of the face plate

Close up of the finish of the right side of the face plate

  • 0
  • 0
After losing a heap of photos from my phone, I cant actually show some progress shots....But back to the face plate -After hours of sculpting and sand

After losing a heap of photos from my phone, I cant actually show some progress shots....But back to the face plate -After hours of sculpting and sand

  • 0
  • 0
Quickly removed the plates from the Disney mask, primed them and added a quick layer of texture spray paint. Let it dry then I sanded it back so it lo

Quickly removed the plates from the Disney mask, primed them and added a quick layer of texture spray paint. Let it dry then I sanded it back so it lo

  • 0
  • 0
I cut off the disney section to graft onto the BS helmet. I also started sanding down and flattening out the chrome section (its way too rounded). Yep

I cut off the disney section to graft onto the BS helmet. I also started sanding down and flattening out the chrome section (its way too rounded). Yep

  • 0
  • 0
Used some plastic car putty (the kind used for repairing bumpers) trying to get rid of the ****** texture on the BS helmet, ultimately hoping to achie

Used some plastic car putty (the kind used for repairing bumpers) trying to get rid of the ****** texture on the BS helmet, ultimately hoping to achie

  • 0
  • 0
6heres the section I cut of the Disney mask to graft onto the BS dome. Ill put it aside for later

6heres the section I cut of the Disney mask to graft onto the BS dome. Ill put it aside for later

  • 0
  • 0
The soldering iron trick didnt feel that sturdy at all so I decided to fibreglass the inside to really sturdy it up. Also it give it some weight which

The soldering iron trick didnt feel that sturdy at all so I decided to fibreglass the inside to really sturdy it up. Also it give it some weight which

  • 0
  • 0
Obviously Ive pulled out all the guts of the Disney mask and gone onto glueing the two sections together. Then I used a soldering iron to melt it toge

Obviously Ive pulled out all the guts of the Disney mask and gone onto glueing the two sections together. Then I used a soldering iron to melt it toge

  • 0
  • 0
Other side

Other side

  • 0
  • 0
Started to smooth and shape up this section with some epoxy putty. Yep it kinda looks like **** here but I promise it looks better down the track!

Started to smooth and shape up this section with some epoxy putty. Yep it kinda looks like **** here but I promise it looks better down the track!

  • 0
  • 0
Just showing the other side of the grafting process. Yep It looks pretty messy here

Just showing the other side of the grafting process. Yep It looks pretty messy here

  • 0
  • 0
Heres the BS helmet and Disney mask side by side. We all pretty much know how this goes down so Ill keep it as brief and interesting as possible.

Heres the BS helmet and Disney mask side by side. We all pretty much know how this goes down so Ill keep it as brief and interesting as possible.

  • 0
  • 0
FettFreak80

Promise this BS Kylo Ren helmet mod is worth looking - Yes Im VERY late to the party

There are no comments to display.

Album information

Album owner
FettFreak80
Date created
Item count
24
View count
779
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

FettFreak80

FettFreak80

Media items
24
Albums
1
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top