Cyberfez's Buffy The Vampire Slayer Scythe build

C

cyberfez

New Member
This is a record of my Scythe build.
Started by cutting shape and sanding and whittling by hand.
11220907_10153566533997578_3500635494873086517_n.jpg18307_10153566604702578_465205241360341529_n.jpg11751789_10153566648432578_4003352624258118919_n.jpg11811472_10153566619272578_7978151319874750608_n.jpg11755096_10153566648387578_8467840926658747853_n.jpg11221599_10153582785662578_4913139538310855492_n.jpg11745404_10153566648372578_3501660448184262656_n.jpg15056340_10154810250457578_4471992346351973719_n.jpg15085707_10154810250537578_5823015731681420060_n.jpg

The headstock I decided to 3d print
15134773_10154810250487578_9008524895669563978_n.jpg
 

Attachments

  • 15032789_10154810251372578_2122999561346774251_n.jpg
    15032789_10154810251372578_2122999561346774251_n.jpg
    63.2 KB · Views: 99
  • 14963171_10154810250982578_6363660429682664462_n.jpg
    14963171_10154810250982578_6363660429682664462_n.jpg
    54.3 KB · Views: 103
  • 14915645_10154810250577578_3483926037645884321_n.jpg
    14915645_10154810250577578_3483926037645884321_n.jpg
    72.6 KB · Views: 89
Started painting the blade
14915645_10154810250577578_3483926037645884321_n.jpg
3D print kept lifting and deforming so I have to do this again sometime but I want to use this on the weekend so had to go with it. screwed and glued it to the blade.
15078873_10154810250712578_4247446666233203298_n.jpg14963171_10154810250982578_6363660429682664462_n.jpg
Blade masked and painted (not too happy with the red but better than nothing.
15036515_10154810251017578_5827495719366505742_n.jpg15085664_10154810250957578_1407663789177564384_n.jpg15095557_10154810250867578_2041480580666675600_n.jpg15095713_10154810250752578_6707421325216563406_n.jpg
started on the handle. Placing the detail in (thumbtacks glued in with 2 part araldite)
15032795_10154810251072578_295073017226673409_n.jpg15078861_10154810250837578_5475927120656490567_n.jpg
I got the measurements from reading about the prop that it was approximately 1 metre in length so I printed out the clearest pic of the Factory Prop one 1:1.
15094249_10154810250792578_7946993939073044468_n.jpg
 
Cut the stake out of walnut dowel and stained it as dark as I could get.
15094359_10154810251137578_2955164187547644196_n.jpg
3d printed the crown and assembled then with glue on the stake.
15073303_10154810251197578_5039211337644074280_n.jpg15170809_10154810251167578_7307142297665893966_n.jpg15094377_10154810251252578_2314338364447746807_n.jpg

finished product not too bad. these shots wer just a stack up before i secured it all down
15134659_10154810251337578_4061768992126392021_n.jpg
Here is it done.
15032789_10154810251372578_2122999561346774251_n.jpg

Miss Kitty Boo
15078590_10154810251612578_5064197720785971696_n.jpg15073476_10154810251557578_1899332431591954667_n.jpg
Me as Caleb
15032910_10154810251462578_6896371626854011312_n.jpg15107244_10154810251407578_8623978075990637171_n.jpg

- - - Updated - - -

Me dressed as Caleb with Scythe and Nathan Fillion
15042283_10154810022057578_1969143908650045371_o.jpg
 
This thread is more than 7 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

Birdie
Buffy AT-4 Rocket Launcher Build.
Replies
0
Views
88
Birdie
Birdie
Birdie
Buffy Rocket Launcher Scope ID?
Replies
7
Views
657
TazMan2000
TazMan2000
Tenaciousbt
The Originals / Vanpire Diaries Props
Replies
1
Views
411
Tenaciousbt
Tenaciousbt
A
2001 Monolith build
4 5 6
Replies
119
Views
2,624
alan molstad
A
Rusty85
Return of the Living Dead Zombie Barrel Build 2.0
2
Replies
24
Views
1,477
Metalalien
Metalalien
Back
Top