Done / Completed Please Delete.

teecrooz

Legendary Member
RPF PREMIUM MEMBER
I'm doing a very limited run of ANM2 Booster cones. These were machined (by dmachinist) using my original as a model. I'm offering 20 of them for sale here. I have a few extra already reserved so I cannot guarantee more than the 20 below.

Note that these fit into both my original booster as well as Roman's booster replica. I have also test-fit it to a more recent run of Russ's steel boosters and it fit that as well.

Please post here and PM me to get on the list. Initial estimate is $45 shipped in the US. International is at cost. So far the US flat rate box cost (which is $5 in the US) to Canada, UK, and France has been $25. So estimate is $65 shipped for international.

1:peacefrog35 - PAID, SHIPPED
2: Marv - PAID, SHIPPED
3: Marv - PAID, SHIPPED
4: Edraven99 - PAID, SHIPPED
5: Edraven99 - PAID, SHIPPED
6: Serenity - PAID, SHIPPED
7: mogaert - PAID, SHIPPED
8: morgan63 - PAID, SHIPPED
9: Adomeitw - PAID, SHIPPED
10: mogaert - PAID, SHIPPED
11: ObiShane - PAID, SHIPPED
12: available
13: available
 

Attachments

  • DSC_0018.JPG
    DSC_0018.JPG
    2.7 MB · Views: 243
  • DSC_0017.JPG
    DSC_0017.JPG
    2.2 MB · Views: 255
  • DSC_0016.JPG
    DSC_0016.JPG
    2.4 MB · Views: 228
  • DSC_0015.JPG
    DSC_0015.JPG
    3 MB · Views: 212
  • DSC_0014.JPG
    DSC_0014.JPG
    3.1 MB · Views: 215
Last edited:
Re: Obi-Wan ANH ANM2 Booster Cones

I don't think there would be any room if you use a spacer such as Romans spacer.
Anyway, put me down on your list please.
Thanks! PF35
 
Re: Obi-Wan ANH ANM2 Booster Cones

Hi Kevin,

You would have to modify an existing spacer. The clamp fits perfectly around the bearing though.
 
Re: Obi-Wan ANH ANM2 Booster Cones

Hi, will this fit with the 3/8 rod that Roman's saber uses for hilt assembly?
 
Re: Obi-Wan ANH ANM2 Booster Cones

Hi, will this fit with the 3/8 rod that Roman's saber uses for hilt assembly?

I'll disasseble my Roman tonight and check for you.

List updated.

- - - Updated - - -

morgan63, I didn't see a PM come through, but I added you to the list.
 
Re: Obi-Wan ANH ANM2 Booster Cones

These are all ready to go out next week. I'll be sending PMs with payment instructions over the weekend.
 
Re: Obi-Wan ANH ANM2 Booster Cones

Did payment instructions get sent out? I didn't see any PM... just checking.
 
Re: Obi-Wan ANH ANM2 Booster Cones

The paid orders are boxed up and going out Monday.
 
Re: Obi-Wan ANH ANM2 Booster Cones

Received mine too! Here it is, after some bluing and a bit of polishing:
B.JPG
(Chris's on left, my real one on right.)

I'm going to try to brighten the steel a little more like the nickel-plating of the real one and maybe soften up the edges with a hammer too.

Thanks for doing these!
 
Back
Top