Star Lord Boot Rocket

xMENNENx

xMENNENx

New Member
Sat down and made this today, it's not 100% accurate obviously but could work for some people.

8RwIShM.jpg


Here are the files if someone wants to make a pepakura file or to 3d print it.

v3 FILES
http://www.4shared.com/file/uAfYOb-oba/baseplate_v3.html

http://www.4shared.com/file/hRR6mlWNce/body_v3.html

http://www.4shared.com/file/_2HXV4Taba/head_v3.html

http://www.4shared.com/file/mp7NeF7Lce/rocket_p1_v3.html

http://www.4shared.com/file/1ZaLDWk8ba/rocket_p2_v3.html

http://www.4shared.com/file/g3dgp9ffce/rocket_p3_v3.html

http://www.4shared.com/file/T0LuUPwqba/rocket_p4_v3.html

http://www.4shared.com/file/F_dAr9Qfba/rocket_p5_v3.html

http://www.4shared.com/file/QVfxRrNpce/rocket_p6_v3.html

http://www.4shared.com/file/IXG8COW7ce/rocket_p6_v3_single.html
 

Attachments

  • 8RwIShM.jpg
    8RwIShM.jpg
    179.9 KB · Views: 540
Last edited:
Printed this today, took about 10 hours at .3mm resolution on my Solidoodle 3 with support. The vertical pins at the bottom of the rocket are super fragile, as well as the top portion of the rockets. Everything came right off as I was trying to remove the support material. Also, inserting the rockets into the body caused the body to crack, so I'll need to fix some fitment issues. Overall it looks great, I just need to tweak a few things and try again!
 
I sliced up the rocket model and rearranged it so I wouldn't need to use support. The result was much better! Though those pins are still quite fragile.

20140702_105136_zpsfsdc6ua7.jpg
 
That print came our awesome! I figured the posts on the rocket would be really fragile. How is the size when assembled? I guesstimated the measurements when modeling it. Any suggestions for improving them are welcome, I'm working on a v2 of the model and will post some updated pictures when I get home from work.
 
Last edited:
Updates!

In all the pictures the v1 model is on the left, the v2 is on the right.

To start here is a comparison shot of the v1 model and the current state of the v2 model side by side
2DYx34Z.jpg




Here is a comparison of the rockets
kw0GW4S.jpg




and a close up of some of the detail
CQjfUki.jpg




the "rocket cores" pulled out of the pins for a better comparison
kZT0Gxc.jpg




the circle on the bottom of the body has been widened and a small ring added inside, as well as some "bolt heads" added to the arms holding the rockets
O9q1VPd.jpg




But the big change so far has been the addition of slots and grooves/ pins and holes to make printing individual pieces easier. I plan to also do this to the rocket components
wLsmPun.jpg

681hg1o.jpg
 
 
Thanks a ton for sharing these files. I notice that the post is fairly old and there are no pictures of a completed booster. Are you still updating/improving the model or do you consider it complete? I was going to start the arduous process of printing one for myself but don't want to do that only to have you post an improved version the next day. Thanks!
 
This thread is more than 5 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

Webberley
Rocket Raccoon Vol. 3 Replica Build
Replies
18
Views
1,150
Webberley
Webberley
mhariush
Hasbro Star-Lord Helmet is back on Sale
Replies
0
Views
658
mhariush
mhariush
Usagi Pilgrim
New Hasbro Star Lord Helmet On The Way
Replies
3
Views
950
Usagi Pilgrim
Usagi Pilgrim
FastballSpecial
Did King Arts ever release their GOTG Vol 1 Rocket Racoon Rifle Blaster?
Replies
0
Views
593
FastballSpecial
FastballSpecial
Z
Where to get star lord jacket?
Replies
2
Views
1,108
Solider
Solider
Back
Top