Iron Man pepakura helmets: Mark 42 43 Iron Patriot WM - PDF Links first post 3D print

gimpee

Active Member
THESE FILES ARE FREE & FOR PERSONAL USE ONLY

Hi.

I started this project two weeks ago after watching the amazing trailer. I will making only the two helmets.

HELMET.jpgIRONPATRIOT11.jpg

First helmet finished:

IRONPATRIOT9.jpg

LINKS:

Download letter size:

Iron Patriot - War Machine Mark 2 by gimpee




Mark XLII MK 42

Mark8.jpg

Download letter size:

Mark 42 - Mark 43_Helmet__by_gimpee


Download A4 size:

Mark 42 - Mark 43_Helmet_A4_by_gimpee


FOAM VERSION - thanks to Gaiatron:

Download letter size:
Mark 42 - Mark 43 _Helmet_FOAM


Download A4 size:
BIGGER SIZE Mark 42 - Mark 43_Helmet_278x203mm

BIGGER SIZE Mark 42 - Mark 43_Helmet_278x203mm PDF

MARK 42/43 HELMET FILES READY FOR 3D Print! -FREE

Thanks to devildog12:
View attachment 512835

Download here: Mark 42/43 Helmet FIles Ready for 3D Print! -FREE


THESE FILES ARE FREE & FOR PERSONAL USE ONLY, for another uses like 3d printings you need to contact me first.

You can say Thank you donating here:
Donate
 
Last edited:
Re: Iron man 3 helmets pepakura files

Wow, nice job.
Bit of comment:
1. WM helmet is too tall?
2. There should be strips on the cheek and forehead
3. Did you smooth out Mk8 helmet? Or just material shading? It's hard to see if rendered like that.
 
Re: Iron man 3 helmets pepakura files

Looks great gimpee. I just think this angle is a little steep. It doesn't seem like it follows the upper areas radius.
 
Re: Iron man 3 helmets pepakura files

Wow, nice job.
Bit of comment:
1. WM helmet is too tall?
2. There should be strips on the cheek and forehead
3. Did you smooth out Mk8 helmet? Or just material shading? It's hard to see if rendered like that.

1. - I think the helmet looks tall due to the viewing angle of pepakura. My mistake.

2. - This helmet is different from the others, i think the front is separated in 3 parts, that is the reason of those lines in the cheek and forehead.

3. - Yes, the mark 8 looks that way because is smoothed.

Looks great gimpee. I just think this angle is a little steep. It doesn't seem like it follows the upper areas radius.

I go to check that, but i think is due the viewing angle too.

bit wider but amazing work so far.

Thanks for the comments.

Modeling the second helmet

IMMK8.jpg



Any feedback is welcome.
 
Last edited:
Re: Iron man 3 helmets pepakura files

the IM is much smoother than the WM/IP model. crossing my fingers on this. will start on this baby after the release. great job you did here.
 
Re: Iron man 3 helmets pepakura files

Don't smooth it if you want to do pep. It'll just creating so much pain
 
Re: Iron man 3 helmets pepakura files-Links in First Post

First helmet finished.

IRONPATRIOT2.jpg

IRONPATRIOT3.jpg

IRONPATRIOT4.jpg

IRONPATRIOT5.jpg

IRONPATRIOT6.jpg

IRONPATRIOT7.jpg

IRONPATRIOT8.jpg

IRONPATRIOT9.jpg

IRONPATRIOT10.jpg

IRONPATRIOT11.jpg



The Faceplate is divided in 3 parts.

Links in the first post.
 
Last edited:
Re: Iron man 3 helmets pepakura files - Links first post

It´s free.
Foam Version added.
 
Last edited:
Re: Iron Patriot - Iron man Mark VIII Helmets pepakura files - Links first post

Very nice Bro, Thanks for sharing!! subscibed :thumbsup
 
Re: Iron Patriot - Iron man Mark VIII Helmets pepakura files - Links first post

gimpee, thank you for this!
 
Re: Iron Patriot - Iron man Mark VIII Helmets pepakura files - Links first post

All the good stuff comes out while i'm sleeping. Now i have to go 10 hours before i can do anything about it. Lol GM
 
This thread is more than 4 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top