Hello everybody,
I am currently researching another Iron Man project: Tony's Repulsor Boot.
I am especially looking for the large object on the backside of the boot and all the little piston connectors. I am pretty sure, the large thingy is a found object. I browsed the net for animatronic piston connectors, but so far I had no luck.
I found some comic con 07 pictures of the original boot, but if anybody has additional photos of the prop, I'd appreciate those.
Cheers,
Thomas
That large piece looks(To me) like a splitter for ABS or a dual braking system from a motorcycle.
I agree that it looks like something automotive based, perhaps a clutch slave cylinder or something along those lines.
Based on the second photo, I would say it is a rear brake master cylinder off of a motorcycle that uses a remote reservoir. The nut, at the bottom, with the loom coming out of it is the brake light switch. Maybe off of a sport bike.
I looked around but cound not find any the had angled ports. I also found some proportioning valves that are similar but still no angled ports.
If this ever get's made and kits are available, I think an interest list would do well. HINT HINT.
Brad
The other thing it looks like and by the size, it looks like a dual air-water sytem that used in arthroscopic surgery, from the older series ( now a days the system dont need 2 seperate vaulves).......
but like u guys said it most likly is from a bike or car.
From when I was checking it out at comic con and in the pics it looks like there is a boot or molded piece for the foot to slide in, proboly rubber cast over the stars actual leg, with tubes and details cast in it, then painted silver with the cage and rest of the piece built over that, might be a good place to start
man, I thought it was cool having the arc reactor sitting on my display table...imagine having that boot too!...
Oh my god! What a nightmare! I'd love to get involved but I seriously think my head would explode if I attempted this!
For all of the little pistons look at RC servo linkages
If I head out to the junkyard this week I am going to pop some hoods and look for that "valve". I know I have seen that somewhere.
Also looks like they used a bunch of RCA and CO-AX connectors.
The big hydraulic cylinders look like two 12g Co2 cartridges cut and welded end to end with a rod running thru them
Very cool guys!
I talked to a frienf who works at a Honda garage and he also said it looks like a master brake cylinder. He'll drop by today with a few samples
Thomas
So far I had no luck searching for the main brake cylinder. I used the google picture search but could not find the piece in question. The Honda guy was also wrong.
Of course, I could scratch the part, but getting the original piece would make it much easier to work from there, as it could be used for measurements of the whole boot.
I was ist denn't even able to find similar small pistons...
Getting a little frustrated here...
I have been looking around and I was thinking the small piston looking bits were some kind of AV jack, but could not find the same look(Found some similar).
TK said it looked like an air water splitter. So I started looking up pneumatic fittings and manifolds. Same results, close but no cigar.
The two piston bits sticking out of the large part look kind of like air chucks but based on the first picture they are to small to be a 1/4 chuck. I looked up air chucks and found some small ones but still similar, not the same.
Focusing on the brass looking sleeves on the side fittings. They definitely look like tiny quick connectors but the center pin is throwing me off.
I agree the "inner boot" looks like a foam rubber with wires molded directly onto it, would be great if we could see it stripped down
I whipped this up(Dodging work) for the large pistons. Scale is off but I used what I had laying around. Smaller cylinders would be right, I think.
Looks good! What are the cylinders originally used for?fuelish said:
I whipped this up(Dodging work
That part looks more like a hydraulic actuator or car spray paint nossle.
Brad
They are CO2 inflators, like you would use in an air pistol or cream whipper. The ones pictured are for bicycle tire inflators. They are sixteen gram. Looking at your photos the 12 gram looks pretty good(I did not have any empties or I would have used the 12s)hollywoodhardware said:
I took a shot of the two sizes.
I don't know that it is how they did it, but I could make one in about 15 minutes. So it seems plausible, rather than them trying to find a similar looking part that fit, they would have made it this way, with stuff they had around.
I have not given up on the large part. I HAVE seen that thing somewhere. I am going to look at some cars I have worked on recently. That may niot be where it comes from, but that is where I would have seen it.
I guess the new Hot Toys Tony Stark Mech Test Figure will help a bit
http://www.sideshowtoy.com/?p=8123
Reply with Quote
