Battlestar Australis

omes72 · 09-27-2010, 04:35 AM

A bit more done. The body is now on. Just needs some adjustment & lining up. Need to cut the acrlic bottom now to wrap around the armature. Should maybe have thought about that before getting the acrylic cut but I guess thats all part of the learning experience. Am happy to have this on & will also connect the arms.
Getting the engine section onto the armature was not fun. I snapped the back brace in the process. Just waiting for my SS Raider parts for the bottom & the rear section is amost complete. I could have my engine plate finished also but think I may rebuild it for the third time as I am still not happy with it....

omes72 · 09-28-2010, 03:01 AM

Got the bady aligned & the floor on. Am so stoked to have the floor on as it had to fit through the armature... I just marked where the pipe was, drew a line though the centre & scored the acrylic with a stanley knife about 50 times then snapped. Luckilly it was a clean break

Have had a few not so clean breaks using that method. I have also in the last day snapped both side panels where I made the slots for the arms to sit in

I then got my mate Mr Dremel & cleared out the pipe cavity on the 2 halves & she sat in nice & snug. Will get the raised panels bevelled noe & scribe the top section. I should also have the arms on within the week. maybe

omes72 · 09-30-2010, 04:51 PM

Just recieved my V1 SS Raider ready for some Dremel action

This is used on the bottom of the engine section. Have also started moulding up some parts. This was one for a friend that I can use also to save the valuable donor parts.

MonsieurTox · 09-30-2010, 06:46 PM

Looking great Jase ! And very nice casting

How do you glue your acrylic parts ? It's very clean !

omes72 · 09-30-2010, 11:15 PM

Quote:

Originally Posted by MonsieurTox

Looking great Jase ! And very nice casting

How do you glue your acrylic parts ? It's very clean !

Thanks Julien. I use 'Weldon #16'. Its an acrylic glue that melts the plastic together slightly. Its excellent for acrylics & styrene. Cures fast but gives enough time for alignment adjustments. Its also very noxious.

MonsieurTox · 10-03-2010, 04:32 PM

Thanks Jase !

Don't have the Weldon line here, so I think I gonna use chloroform, but it doesnt allow any adjustement :/

omes72 · 10-03-2010, 08:48 PM

I could send you a tube Julien?

So just shredded a perfectly good Salzo V1 Raider to start detailing the bottom engine deck. The moto tool carved her up real fast. Always do cutting & drilling of resin outside & wear a mask & goggles. I learnt the hard way. Trust me. Am happy to have these to build this section up now.

MonsieurTox · 10-06-2010, 09:20 AM

Quote:

Originally Posted by omes72

I could send you a tube Julien?

So just shredded a perfectly good Salzo V1 Raider to start detailing the bottom engine deck. The moto tool carved her up real fast. Always do cutting & drilling of resin outside & wear a mask & goggles. I learnt the hard way. Trust me. Am happy to have these to build this section up now.

Thanks Jase, but I doubt this kind of stuff would be allowed in a plane ? lol
I think I can find something similar here, maybe under another brand... Thanks for the offer though !

Man you're crazy, cutting a kit like that !
And wow all that resin dust... I'm affraid with a tiny amount of resin dust on my workbench, I couldnt cut the resin like that lol even with gloves and mask ! Obviously you didnt wear gloves, I hope you were wearing at least a mask...

whitepearl · 10-06-2010, 09:44 AM

Great jod, it's just amaizing!!! where did you find all the parts to do it??? Never I was thinking to use tank parts to do ship's size!! incredible scratch!!

BubbaHoTep · 10-06-2010, 10:46 AM

Very cool build, some you on here just blow me away!

omes72 · 10-10-2010, 11:14 PM

Panel lines drawn up for scribing. Once these are done I will bevell/angle the raised panels.

omes72 · 10-11-2010, 04:44 AM

8 hours later & have completed the scribing. have given a dusting of primer to mark out the raised panel positions for when Ivee bevelled/angled the edges. Was a big job & am relieved to another section out the way. Will build the arms next. thanks for looking.

whitepearl · 10-11-2010, 04:53 AM

Awesome work on it !!!!!8 hours to do it, incredible...Amaizing

omes72 · 05-21-2011, 01:02 AM

Have built the neck & arms after some time off the project on other things. Using the new skills of phot scaling I have learnt am now working primarilly from scaled photos & kit parts. Build is preogressing nicely now with the confidence of using these new techniques I have learnt. Am about to start the head & Landing Bays very soon. I will not detail models before base structures are finished any more as flipping the models to work can be very hazardous. Just a learning curb as I am still a beginner. I discovered that the neck(and most of this studio model) are asymetrical meaning not even on port & starboard side in many places. I have incorporated these inacuracies into my build following the scaled photos as closely as possible. Thanks for looking

omes72 · 09-21-2011, 01:27 AM

Finally had the last of the sections laser cut to build the head & landing bays.
Am really excited to get these sections built up so I can flip her over & start on the coffin & support arms.

ringa · 09-21-2011, 07:11 AM

Those look great, Jase. It all looks great. Seeing this makes me think that if I ever do another huge SS model, I will have to start getting things laser cut. I must go through hundreds of X-acto blades and a whole lot of sand paper in a single build.

omes72 · 10-02-2011, 04:52 PM

Thanks Rick.

Have started assembleing the landing bays.
These are quite tricky to get right so need to make sure Im checking the reference.
I also need to fix my neck as I didn't make detachable forgetting I needed to have access for lighting....
So will work on fixing that today.

3d-builder · 10-02-2011, 07:28 PM

WOW man thats just sexy.........where have you been?
Whats up with the SS Escape Pod?

omes72 · 10-02-2011, 11:06 PM

Hey Michael its good to see you back.
Hope your Traithalons went well mate.
The Escape Pod is still on the bench.
Just having a crack at the Battlestar as I got the last of my acrylics cut to finish the superstructures so I can concentrate on kit bashing

I also have the frame & hulls cut for my ANH Devestator that I will post later.
You will love that.
Stay around mate I can always do with good advice when Im stuck on something.

SOXMIS · 10-02-2011, 11:45 PM

Hi Jason, your build looks fantastic mate! Do you know a chap called Brad, up near Brizzy? He was building studio scale Battlestars a few years back. He used to be a member here, not sure if he still is. Anyway, fantastic work!

ozzyguanche · 10-03-2011, 12:27 AM

I dont know were you find the time!!! But I am glad you do. Love watching the builds.

May have to drop in next time I am up your way to see it in person.

Ozzy

sleepless · 10-04-2011, 07:47 AM

Hey Jason looking good buddy I will have to get down there so we can drag mine out. Still on honeymoon atm

Brad

omes72 · 10-05-2011, 04:04 AM

Shes still here mate.
Congratulations also on tieing the knot.
Hope you have a good time.

sleepless · 10-05-2011, 07:40 AM

Quote:

Originally Posted by SOXMIS

Hi Jason, your build looks fantastic mate! Do you know a chap called Brad, up near Brizzy? He was building studio scale Battlestars a few years back. He used to be a member here, not sure if he still is. Anyway, fantastic work!

Hey thats me. Jason and I are doing some work together, my Galactica is currently at his place for some refurbshment and completion, much appreciated Jase

		Replica Props	Screen Used Props	Replica Costumes	Sculpture and Makeup	General Modeling	Studio Scale Models	Movie Discussion
	Collaborate, create, and collect at the internet's largest community dedicated to props, costumes and models.

09-27-2010, 04:35 AM	#26
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis A bit more done. The body is now on. Just needs some adjustment & lining up. Need to cut the acrlic bottom now to wrap around the armature. Should maybe have thought about that before getting the acrylic cut but I guess thats all part of the learning experience. Am happy to have this on & will also connect the arms. Getting the engine section onto the armature was not fun. I snapped the back brace in the process. Just waiting for my SS Raider parts for the bottom & the rear section is amost complete. I could have my engine plate finished also but think I may rebuild it for the third time as I am still not happy with it.... Attached Thumbnails

09-28-2010, 03:01 AM	#27
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Got the bady aligned & the floor on. Am so stoked to have the floor on as it had to fit through the armature... I just marked where the pipe was, drew a line though the centre & scored the acrylic with a stanley knife about 50 times then snapped. Luckilly it was a clean break Have had a few not so clean breaks using that method. I have also in the last day snapped both side panels where I made the slots for the arms to sit in I then got my mate Mr Dremel & cleared out the pipe cavity on the 2 halves & she sat in nice & snug. Will get the raised panels bevelled noe & scribe the top section. I should also have the arms on within the week. maybe Attached Thumbnails

09-30-2010, 04:51 PM	#28
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Just recieved my V1 SS Raider ready for some Dremel action This is used on the bottom of the engine section. Have also started moulding up some parts. This was one for a friend that I can use also to save the valuable donor parts. Attached Thumbnails

09-30-2010, 06:46 PM	#29
MonsieurTox Join Date: Jun 2006 Location: Paris, France Posts: 2,806	Re: Battlestar Australis Looking great Jase ! And very nice casting How do you glue your acrylic parts ? It's very clean !

( Don't want to see advertising between posts? Register for free and become a member of our community! )
RPF Sponsors

10-03-2010, 04:32 PM	#31
MonsieurTox Join Date: Jun 2006 Location: Paris, France Posts: 2,806	Re: Battlestar Australis Thanks Jase ! Don't have the Weldon line here, so I think I gonna use chloroform, but it doesnt allow any adjustement :/

10-03-2010, 08:48 PM	#32
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis I could send you a tube Julien? So just shredded a perfectly good Salzo V1 Raider to start detailing the bottom engine deck. The moto tool carved her up real fast. Always do cutting & drilling of resin outside & wear a mask & goggles. I learnt the hard way. Trust me. Am happy to have these to build this section up now. Attached Thumbnails Last edited by omes72; 10-03-2010 at 10:30 PM.

10-06-2010, 09:44 AM	#34
whitepearl Join Date: Oct 2010 Location: France, near Paris Posts: 12	Re: Battlestar Australis Great jod, it's just amaizing!!! where did you find all the parts to do it??? Never I was thinking to use tank parts to do ship's size!! incredible scratch!!

10-06-2010, 10:46 AM	#35
BubbaHoTep Join Date: Sep 2010 Location: Kentucky Posts: 72	Re: Battlestar Australis Very cool build, some you on here just blow me away!

10-10-2010, 11:14 PM	#36
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Panel lines drawn up for scribing. Once these are done I will bevell/angle the raised panels. Attached Thumbnails

10-11-2010, 04:44 AM	#37
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis 8 hours later & have completed the scribing. have given a dusting of primer to mark out the raised panel positions for when Ivee bevelled/angled the edges. Was a big job & am relieved to another section out the way. Will build the arms next. thanks for looking. Attached Thumbnails

10-11-2010, 04:53 AM	#38
whitepearl Join Date: Oct 2010 Location: France, near Paris Posts: 12	Re: Battlestar Australis Awesome work on it !!!!!8 hours to do it, incredible...Amaizing

05-21-2011, 01:02 AM	#39
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Have built the neck & arms after some time off the project on other things. Using the new skills of phot scaling I have learnt am now working primarilly from scaled photos & kit parts. Build is preogressing nicely now with the confidence of using these new techniques I have learnt. Am about to start the head & Landing Bays very soon. I will not detail models before base structures are finished any more as flipping the models to work can be very hazardous. Just a learning curb as I am still a beginner. I discovered that the neck(and most of this studio model) are asymetrical meaning not even on port & starboard side in many places. I have incorporated these inacuracies into my build following the scaled photos as closely as possible. Thanks for looking Attached Thumbnails

09-21-2011, 01:27 AM	#40
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Finally had the last of the sections laser cut to build the head & landing bays. Am really excited to get these sections built up so I can flip her over & start on the coffin & support arms. Attached Thumbnails Last edited by omes72; 09-21-2011 at 01:34 AM.

09-21-2011, 07:11 AM	#41
ringa Join Date: Mar 2007 Posts: 315	Re: Battlestar Australis Those look great, Jase. It all looks great. Seeing this makes me think that if I ever do another huge SS model, I will have to start getting things laser cut. I must go through hundreds of X-acto blades and a whole lot of sand paper in a single build.

10-02-2011, 04:52 PM	#42
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Thanks Rick. Have started assembleing the landing bays. These are quite tricky to get right so need to make sure Im checking the reference. I also need to fix my neck as I didn't make detachable forgetting I needed to have access for lighting.... So will work on fixing that today. Attached Thumbnails

10-02-2011, 07:28 PM	#43
3d-builder Join Date: Jan 2009 Posts: 1,394	Re: Battlestar Australis WOW man thats just sexy.........where have you been? Whats up with the SS Escape Pod?

10-02-2011, 11:06 PM	#44
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Hey Michael its good to see you back. Hope your Traithalons went well mate. The Escape Pod is still on the bench. Just having a crack at the Battlestar as I got the last of my acrylics cut to finish the superstructures so I can concentrate on kit bashing I also have the frame & hulls cut for my ANH Devestator that I will post later. You will love that. Stay around mate I can always do with good advice when Im stuck on something.

10-02-2011, 11:45 PM	#45
SOXMIS Join Date: Dec 2010 Location: Guangzhou, China Posts: 16	Re: Battlestar Australis Hi Jason, your build looks fantastic mate! Do you know a chap called Brad, up near Brizzy? He was building studio scale Battlestars a few years back. He used to be a member here, not sure if he still is. Anyway, fantastic work!

10-03-2011, 12:27 AM	#46
ozzyguanche Join Date: Nov 2006 Posts: 374	Re: Battlestar Australis I dont know were you find the time!!! But I am glad you do. Love watching the builds. May have to drop in next time I am up your way to see it in person. Ozzy

10-04-2011, 07:47 AM	#47
sleepless Join Date: Feb 2004 Posts: 167	Re: Battlestar Australis Hey Jason looking good buddy I will have to get down there so we can drag mine out. Still on honeymoon atm Brad

10-05-2011, 04:04 AM	#48
omes72 Join Date: Jun 2009 Location: Gold coast Queensland Terra Australis Posts: 623	Re: Battlestar Australis Shes still here mate. Congratulations also on tieing the knot. Hope you have a good time.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What Battlestar from what colony	kca832	Replica Movie Props	5	11-30-2010 02:34 AM
Battlestar Images	ThomasModels	General Modeling	14	04-21-2007 10:18 AM
Anyone help me? Battlestar New series	Jedi Bailinkski	Replica Movie Props	17	10-05-2006 08:12 PM
Battlestar	Jedi Bailinkski	Replica Movie Props	13	03-05-2006 10:01 PM
My Battlestar	Tordoc	General Modeling	3	02-02-2006 02:08 AM